User confirmed LFE5U-45F-8BG381C (commercial) is the intended part,
matching every other reference in this project. Also corrects this
chapter's own earlier temperature figures: commercial grade is real
TJ 0 to +85C, industrial is TJ -40 to +100C (an earlier draft of this
section had the industrial range wrong at -40/+85C). Same "-8" speed
grade in both -- the letter suffix only changes the characterized
temperature range. KiCad library still needs the part number itself
corrected from ...381I to ...381C.
Compiled clean (47 pages, 0 errors).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
User confirmed TLV62568 (U1) outputs 1.1V, explaining the +1V1 label
found near the VCCAUX ferrite (L2) during the schematic review: it
belongs to U1's own real output net, merely nearby on the page layout,
not routed through the ferrite. VCCAUX remains 2.5V as required by the
real Lattice datasheet.
All three schematic "open items" from the earlier review are now
resolved: TLV62568 EN (R3=499k, confirmed via BOM), the +1V1 label
(false alarm, explained above), and the JTAG pull-up array (confirmed
8 discrete 0402 parts via BOM, not a bussed package -- no polarity
limitation). Only the boot-flash net-name typo (FGPA/FPGA + SCLK/CLK)
remains as a real, open schematic fix, and the FPGA grade discrepancy
(8BG381I vs 8BG381C) remains to be confirmed.
Compiled clean (47 pages, 0 errors).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
User confirmed the real schematic has SDRAM CAS#=F7/WE#=F9 -- matches
this chapter exactly. The earlier review's "appear swapped" finding
was a misread of the schematic image, not a real error; moved from
"real findings" to a cleared checked-item note.
TLV73325's EN pin resolved: direct wire to +3.3V (VIN), always-enabled
-- no soft-start timing requirement like TLV62568's own R3 pull-up (a
plain LDO, no sequencing note in TI's own datasheet), and no dynamic
enable/disable control exists elsewhere in this design.
Remaining real, open finding: the boot-flash net-name mismatch
(FGPA/FPGA typo + SCLK/CLK) still needs a schematic fix.
Compiled clean (47 pages, 0 errors).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
Real KiCad-exported BOM added to the hardware chapter, cross-checked
against every component value this chapter already specifies -- most
match exactly (R1/R2 feedback divider, L1/L2, ferrite part number, all
three real ICs). One real discrepancy found: U2 is captured as
LFE5U-45F-8BG381I (industrial grade) while every other reference in
this project uses the C (commercial) grade part -- flagged, not
resolved, needs explicit confirmation.
Also resolves three earlier open items from the schematic review:
R3=499k confirms TLV62568's EN is populated; R5-R12 being 8 discrete
0402 resistors (not a multi-resistor array) confirms the JTAG
pull-up/down polarity concern doesn't apply; U5 confirms the
previously-missing 16MHz oscillator is now present.
Compiled clean (47 pages, 0 errors).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
Adds a dated review section recording today's actual schematic check
against every real ball assignment in this chapter: confirmed-correct
items, two real findings needing correction (boot-flash net-name
mismatch FGPA/FPGA typo + SCLK/CLK label mismatch that would leave the
flash electrically disconnected from the ECP5's config engine; SDRAM
CAS#/WE# appearing swapped vs. the verified F7/F9 assignment), and
open items not resolvable from the schematic image alone (regulator EN
pins, a stray +1V1 label near the VCCAUX ferrite, JTAG pull-up/down
array polarity).
Also reserves a "PCB module form factor" section (castellated-edge SMD
module, ~50x25mm) for the future physical layout.
Compiled clean (46 pages, 0 errors).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
Datasheet and pinouts.md updated to the current, real state after
today's session: flash #1 was implemented then removed (user's own
MHz-over-persistence priority call), the clock-closure table now
shows the post-revert, post-DEC-0042 numbers (N_SLOTS=4 @ 64MHz 8/8,
worst 64.55MHz/best 72.37MHz; N_SLOTS=8 deferred by explicit user
request), and the FPGA_DATA_READY any_pending formula is updated to
the real counter-based implementation (credited to the user's own
diagnosis) that fixed the last failing N=4 seed.
Compiled clean (45 pages, 0 errors).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
Adds a real, dated section to ch.10 (Hardware and board) covering the
two-independent-flash architecture (neural-network data vs. boot
bitstream), the ESP32<->ECP5 JTAG-only link, and the real CABGA381
ball assignments (JTAG/PROGRAMN/INITN/DONE/CFG[2:0]/MSPI dedicated
pins), matching decisions.log DEC-0041.
Also closes ch.7's (Host interface) own long-standing "still needed"
list: the physical transport (spi_host_bridge.v) and the completion-
notification path (FPGA_DATA_READY) it used to flag as missing are
both now real -- described with the same system-idle-detector formula
implemented in the RTL.
Compiled clean (44 pages, 0 errors).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
Establishes the real ESP32<->ECP5 programming architecture: flash #1
(neural-network data, existing V1 subsystem, ball reserved not yet
wired into V2) stays separate from flash #2 (boot bitstream, MSPI
auto-boot, CFG[2:0]=[0,1,0]); ESP32 talks JTAG only (bit-banged, no
hardware JTAG-master peripheral on S3/C6), updating flash #2 through
the ECP5's own internal sysCONFIG-to-SPI bridge, never driving the
flash pins directly -- zero bus contention, confirmed against the real
Lattice hardware checklist and sysCONFIG user guide.
Adds real, verified ball assignments (official Lattice CABGA381 CSV +
Project Trellis iodb.json) for JTAG, PROGRAMN/INITN/DONE, CFG[2:0],
and the MSPI dedicated pins -- all written to docs/pinouts.md.
Implements FPGA_DATA_READY as real RTL: a system-idle detector
(dependency_manager's any_pending OR neural_director's !queue_empty OR
any active slot), sticky on the busy->idle edge, self-clearing on new
work -- not a per-neuron completion pulse, which was confirmed too
fine-grained. Bit-exact regression re-verified at N_SLOTS=4 and 8
(zero cycle-count change), new explicit data_ready assertion check
added to the D-Stress testbench (PASS both configs), and a fresh
Yosys+nextpnr-ecp5 placement check (0 errors, data_ready placed at G3).
Also fixes a real, independently-found bug while editing an adjacent
file: nms_neural_multiprocessor_sdram_unified.v's own sdram_a port was
still [11:0] (12 bits), stale from before the 64MB/13-bit memory
upgrade. Not exercised by the real board-level top (which wires SDRAM
directly, bypassing this wrapper) but WAS silently truncating A12 in
every D-Stress simulation this session, including today's earlier
ERR-0029 verification runs. Assessed impact: all D-Stress test
addresses used this session decode to rows under 4096 (bit 12 never
actually needed), so no false-positive PASS is believed to have
resulted -- but the full 64MB space was never actually exercised
through this wrapper. Fixed; re-verified bit-exact with identical
cycle counts.
See decisions.log DEC-0041 for full detail.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
Was a separate, untracked directory (DataSheet/) outside the repo.
Renamed to lowercase and moved in as hardware/v2/docs/datasheet/, with
its own .gitignore for LaTeX build byproducts (compiled PDFs stay
tracked, .aux/.log/.toc/etc do not). Now versioned and shares this
repo's own remote instead of living untracked on disk.
Content: IT+EN LaTeX chapter sources, reference manufacturer PDFs, and
compiled datasheet PDFs including the 2026-09-07 SDRAM upgrade
addendum (AS4C32M16SB-7BIN part/pinout/timing) in the v2-en chapters.
Note: hardware/v2/docs/DatasheetLatex/ (and the v1 sibling) is a
separate, already-tracked, differently-structured LaTeX document that
predates this move -- left untouched, not merged, since its chapter
set and content differ and merging was not requested.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_013xXuuRUWZScuo1DeYJxs3v
micheleandClaude Sonnet 5