Adds result_writeback.v, one instance per packed_slot.v, writing each
completed job's result directly into DDR3 at the job's own
result_addr_a/b instead of driving literal top-level pins -- the same
architectural shape as the weight-fetch path, in reverse. job_done now
means "durably in DDR3", not "captured in a register only a pin could
see". n2_system_ddr3_top.v's own s0_result_data_a/b, s1_result_data_a/b
top-level package pins are removed (and the now-dangling XDC constraint
for them), closing the real, hard scaling blocker docs/ARCHITECTURE_
ANALYSIS.md flagged since EXP-0074/0079 (8 bits x 2 lanes x N cores ->
256 pins at N=16).
Addressing reuses the exact same JOB_ADDR_WIDTH->ctrl-bus-word
truncation x_base_a/w_base already use (verified against act_tile_
fetch.v's/layer_prefetch_ctrl.v's own real code, not guessed). The host
reads results back via the already-existing READ_MEM (0x02) SPI opcode
-- no new protocol. A real EXP-0066-class bug (issuing ctrl_req before
mem_grant) was caught and fixed before ever compiling, by re-deriving
the design against act_tile_fetch.v's own proven S_MEMWAIT/S_GAP
sequencing.
Verified two ways: tb_packed_slot.v extended with a real DDR3
read-after-write check (9/9 PASS, confirms the write actually landed,
not just that job_done pulsed); tb_n2_system_ddr3.v re-run via real
xsim to confirm correct behavior under real 2-slot shared-bus
arbitration (8/8 PASS, 0 errors, consistent timing with EXP-0087's own
baseline for this workload).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01MUG92aM9m68TRc4rG55BcC
User-requested hardware notification so the ESP32 can be
interrupt-driven instead of polling STATUS in a loop.
spi_host_bridge_v3.v: new job_out_done input (wired from
neural_director_packed.v, already available at the top level) and new
data_ready_n output. A sticky irq_pending register sets on job_out_done
(latched, survives the pulse itself deasserting) and clears when the
host completes a real STATUS (0x20) or REG_READ(0x02) transaction -
reusing cs_rose, the same real transaction-complete event the module
already relies on elsewhere, not a new mechanism. dir_error is ORed in
live/combinational, not latched. SET has priority over CLEAR on the
rare cycle both coincide.
Real pin: D14, bank 15 (already 3.3V, alongside the SPI bus and
sys_rst) - tentative, not yet a final board decision. Deliberately
added after EXP-0084's own P&R iterations settled, so it didn't
complicate that already-tight I/O/VCCO budget mid-fix. Its own real
P&R verification is deferred to the next real P&R run (already needed
to close EXP-0084's clock-period timing gap), not run separately
against a config already known to fail timing for unrelated reasons.
Real verification: tb_spi_host_bridge_v3.v extended with 10 new checks
(idle state, sticky set, mid-transaction hold, real-acknowledge clear,
unrelated-register non-acknowledge, dir_error live assert/clear).
49/49 PASS.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01MUG92aM9m68TRc4rG55BcC
Real 32-bit DDR3 widening (2x MT41J128M16JT-125:K chips ganged in
parallel, user's own MIG wizard session). Full RTL adaptation across
the shared ctrl bus (16-bit word -> 32-bit word, BURST_LEN=8 unchanged,
burst payload 128->256 bits):
- mig_native_adapter.v: app_wdf_data/app_rd_data 64->128 bits (real,
confirmed against the regenerated MIG wrapper), beat count unchanged.
- act_tile_fetch.v: real logic change - burst now holds 4 tiles instead
of 2 (sel_lat extended to 2 registered bits, 4-way case mux instead
of 2-way ternary, same request-time-registered-select discipline as
EXP-0081). Not a further bytes/MAC reduction, just what's needed to
keep 100% packing utilization at the larger burst.
- host_mem_bridge.v: real addressing redesign - host-facing 16-bit-word
contract kept unchanged (ESP32 firmware unaffected), internally
translated onto the new 32-bit-native ctrl bus.
- sdram_arbiter_n.v, layer_prefetch_ctrl.v, packed_slot.v,
ddr_prefetch_mgr.v, n2_system_ddr3_top.v: mechanical width bump plus
doubled ddr3_dq/dqs/dm pins and the real differential sys_clk/clk_ref
top-level ports the regenerated MIG now requires.
New burst_mem_model32.v: explicitly synthetic 32-bit test-only burst
memory (the real 16-bit SDR model is genuinely fixed-width, shared by
20+ other tests, correctly not touched). Found and fixed a real
address-aliasing bug in it during bring-up (MEM_ADDR_BITS=16 silently
wrapped a real 0x10000 test address to 0).
Real verification: all isolated testbenches re-verified (10/10, 33/33,
32/32, 7/7, 9/9 PASS), plus real xsim against the real 2-chip DDR3
model (tb_mig_native_adapter.v 12/12 PASS, tb_n2_system_ddr3.v 8/8
PASS, both chips visibly returning different real data).
Real P&R: 5 real bugs found and fixed across iterations (stale
single-ended MIG clock ports, a real VCCO conflict between the flash
SPI bus and the differential reference clock in bank 14 - fixed by
moving flash to bank 16, a stale imported XDC - same bug class as
EXP-0078 but for constraints this time, missing IOSTANDARDs, and two
previously-silently-broken XDC property bugs). Route completes 100%,
but real timing does NOT close: WNS -0.618ns, 213 failing endpoints.
Honest root cause: the violation is inside neural_processor_packed.v's
own packed-MAC accumulation tree, unchanged since EXP-0059 - it has
real margin at the old 155.039MHz ui_clk but not at the new 172.414MHz
the paired clock-period change produced. This is NOT caused by the
32-bit width change itself. Width alone, even at the old clock, already
delivers the full intended 2x bandwidth gain (1.24 -> ~2.48 GB/s) -
width and clock rate are separable levers. Current trustworthy timing
signoff remains EXP-0083 (16-bit, +0.073ns) until the clock period is
reverted toward 3225ps (keeping Data Width=32) in one more real,
user-gated MIG wizard session.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01MUG92aM9m68TRc4rG55BcC
Implements the user's board architecture: config flash wired
exclusively to the FPGA, host (ESP32) reaches it only through the
FPGA. flash_spi_master.v is a plain byte-wide SPI master using
STARTUPE2 to reclaim CCLK after configuration (the real, Xilinx-
documented "indirect SPI flash programming" technique, UG470 p94-96).
New opcode 0x40 FLASH_XFER in spi_host_bridge_v3.v relays bytes
byte-for-byte between host and the physical flash bus -- the host
decides the exact SPI NOR command sequence (verified against the real
W25Q32JV datasheet), this RTL knows nothing about flash semantics.
Found and fixed two real bugs during verification: a byte-assembly
off-by-one in flash_spi_master.v, and a genuine protocol-latency bug
in the FLASH_XFER opcode's response timing (needed 2 trailing margin
bytes, not 1 -- the internal flash transfer doesn't start until the
triggering byte finishes, so 1 byte of margin isn't enough). 39/39
tests pass end to end (host SPI -> bridge -> flash_spi_master ->
behavioral flash model).
Wired into n2_system_ddr3_top.v with real pin constraints (flash_mosi
=K17/flash_miso=K18/flash_cs_n=L13, the same pins reserved-but-unused
in EXP-0075) and BITSTREAM.CONFIG.PERSIST=FALSE made explicit.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01MUG92aM9m68TRc4rG55BcC
Found a real, previously-masked bug in spi_host_bridge_v3.v's physical
layer (inherited unchanged from V1/V2): the bit_count==0 MISO bypass
corrupts the last bit of any multi-byte response whose value happens
to end in a 1 -- every prior test's response data coincidentally
ended in 0, hiding it until the new DEVICE_ID register (0x...01)
exposed it via a real bit-exact mismatch. Fixed by removing the
bypass (verified unnecessary for this protocol's actual usage).
Added REG_WRITE/REG_READ opcodes (0x30/0x31) and a register file
(DEVICE_ID/CONTROL/STATUS/N_SLOTS) for general device control beyond
job submission, per explicit user request. Full regression: 38/38
PASS, including new cases specifically targeting the bit-corruption
bug for both REG_READ and READ_MEM.
New hardware/v3/constraints/n2_system_ddr3_top.xdc: reserves the
FPGA's dedicated Master-SPI config-flash pins (found colliding with
auto-placed design ports in the real routed checkpoint) and assigns
the neural-processor management SPI to real, verified-free, edge-
adjacent pins on xc7a100tcsg324-2.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01MUG92aM9m68TRc4rG55BcC
micheleandClaude Sonnet 5