BT1035Driver::boot() had zero retry on the reset+AT-init sequence — a
single hardware RESET# pulse followed immediately by AT commands,
with no second attempt if the module didn't come up in time. This is
the most plausible explanation for the intermittent "no spontaneous
UART bytes after hardware reset" / "AT init failed" boot failures
logged in docs/si4684-rf-investigation-report.md and observed again
live this morning on otherwise-identical hardware/wiring — classic
power-up timing jitter, not a permanent fault. Extracted the reset+
init sequence into resetAndInitOnce() and wrapped it in a 3-attempt
retry loop with a short delay between attempts; the one-time GPIO
config and UART driver install stay outside the loop since they don't
need repeating. Root cause of the underlying jitter is still open.
BluetoothJson.hpp was the only *Json.hpp module in the core with zero
host test coverage (status/scan/paired serialisation, auto-reconnect/
connect/speaker parsing) — every sibling module already has one.
Added bluetooth_json_test.cpp following the existing tuner_json_test
pattern; ctest now covers 20 suites instead of 19.
Documentation catch-up, found doing a full firmware re-review at the
user's request:
- POST /api/tuner/calibrate-antenna and the antcap field on
POST /api/tuner/tune (added in a previous commit, never documented)
are now in ch-api.tex.
- kFirmwareVersion was still hardcoded "0.8.5" despite the RF fixes,
BLE provisioning, phone streaming, antenna calibration, and generic
DSP param API landed since that version's actual release commit
(0a1188a). Bumped to 0.9.0 everywhere it's mentioned (health JSON,
the manual's title page, intro, classes, and API chapters).
- instructions.md and docs/TODO.md still described the firmware as
frozen at 0.8.5 awaiting hardware-in-the-loop testing that has since
happened extensively; docs/TODO.md's H5 verdict specifically still
said "suspect U6 RF ground (re-open PCBWay)" for a bug that turned
out to be firmware, not hardware — actively misleading, corrected.
Both files now summarise the post-0.8.5 HIL findings and current
open items (BT1035 root cause, intermittent HTTP unresponsiveness
under load, antenna-limited signal quality, possibly-undersized 24 KB
nvs partition).
Verified: idf.py build, doxygen (0 warnings), check-manual-sync,
check_si4684_blobs, ctest (20/20), two-pass xelatex manual build all
green. Flashed and confirmed live: fw reports 0.9.0, BT1035 booted on
the first attempt post-flash.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0178rASQ6ZETPMUamvpoR2KR
Confirmed live tonight that the Si4684's automatic front-end tuning
(FE_VARM/VARB properties) is measurably suboptimal on this board: a
129-value ANTCAP sweep (0-128, AN851 Appendix A) at four different FM
frequencies found antcap=102 beats auto-tune by +6 to +11 dB RSSI and
+3 to +11 dB SNR everywhere tested, consistent with the front-end
network component mismatch already logged in
docs/si4684-rf-investigation-report.md — the board's actual matching
network differs from the AN851 reference network those auto-tune
constants were derived from, so a fixed empirical override
compensates for a gap the chip's own algorithm can't see.
Wiring, bottom to top:
- Si4684Driver::tuneFm() already took an antCap byte; threaded it
through core::ITuner::tuneFm() and si4684::Si4684Tuner::tuneFm() as
a new parameter (default 0 = auto, unchanged behaviour for every
existing caller).
- TunerService::tuneFm() takes an optional override instead: omitted,
it falls back to a new defaultFmAntCap_ member so every ordinary FM
tune (seek, scan, station recall, live UI) benefits automatically
once calibrated, not just calls that pass antcap explicitly.
- POST /api/tuner/tune gained an optional "antcap" field for sweeping
live without touching the saved calibration.
- POST /api/tuner/calibrate-antenna commits a sweep result: writes it
to the 24AA025E48 EEPROM's user-writable region (word address 0x00,
separate from the factory-locked EUI-48 at 0xFA-0xFF) via a new
Eeprom24aa::writeFmAntCap()/readFmAntCap() pair, and immediately
updates the live TunerService default — no reboot needed to take
effect, though HardwareBootstrap::boot() also loads it at every
boot so it survives power cycles. Same net::AntennaCalibration
function-pointer bridge pattern as PhoneStreamSink/BleProvisioning,
so components/net stays free of eeprom24aa headers.
Verified end to end on hardware: swept and found 102, saved it via
the new endpoint, confirmed the live default changed immediately,
then power-cycled and confirmed the boot log reports "FM ANTCAP
calibration loaded: 102" and a subsequent default tune reflects it.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0178rASQ6ZETPMUamvpoR2KR
New core::IDsp::writeRawParam(address, value) safeloads any named
Parameter RAM cell in the compiled SigmaStudio program (74 cells: mixer/
Beep1/PEQ coefficients/limiter thresholds/etc — the same set SigmaStudio's
own Remote Connection, components/net/SigmaStudioTcpServer, already has
full access to). Value is a plain SigmaStudio floating coefficient,
converted to ADAU 8.23 fixpoint via the existing core::floatToFixpoint823.
Adau1701ParamTable.hpp holds the name->address table extracted from
Firmware/ADAU1701-Firmware/DigiRadio_IC_1_PARAM.h; core::DspParamJson
handles the wire format without core/ depending on the adau1701 driver
(net/SetupWebServer.cpp bridges the two, consistent with how other
JSON DTOs are supplied their data by the net layer).
GET /api/dsp/params lists every cell (name + address) for discovery.
PUT /api/dsp/param {"name":...,"value":...} writes one. Deliberately no
domain validation, matching the trust level already implied by the
existing SigmaStudio TCP bridge being reachable on the same network.
HTTP routes were registered in the SetupWebServer.cpp change committed
alongside the FM band scan feature (3a10ed7).
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0178rASQ6ZETPMUamvpoR2KR
New TunerService::scanFullFmBand(): tunes to the band bottom then seeks up
repeatedly (reusing the existing hardware-seek + RDS-name-poll machinery
from scanForStation()) until the sweep wraps back around, collecting every
station that clears the existing scan RSSI/SNR thresholds. Returns the
list without touching saved presets or leaving the tuner in any particular
place — callers decide what to do with the results.
New POST /api/tuner/scan/full endpoint (core::TunerFmScannedStation DTO,
serializeTunerFmBandScanJson). Blocks for the whole sweep like the existing
/api/tuner/scan.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0178rASQ6ZETPMUamvpoR2KR
Streaming (main feature this session):
- New WebRadioConfig/WebRadioJson core types, ISecureStore-backed persistence
- New webradio::WebRadioService (thread-safe live config) + GET/POST /api/streaming
- web_radio_stream task now runtime-toggleable (no reboot), no hardcoded URL
- Content-Type diagnostic: warns clearly when a URL is a webpage, not an audio stream
Boot cleanup:
- Removed boot-time auto FM/DAB tune, auto-beep, and the (now-concluded) Si4684
crystal IBIAS/CTUN empirical sweep from main.cpp — tuning/beep are on-demand
via the existing REST API only
Web UI:
- Modernized styling (cards, gradients, toggle switches, light/dark theme)
- New Stream tab wired to /api/streaming
Fixes found via real idf.py build (not just clangd):
- Restored wrongly-removed si4684/Si4684Tuner.hpp include in main.cpp
- Fixed MP3Decode() argument types in web_radio_stream.cpp (unsigned char**/int*)
Quality-gate fixes:
- Host-test stub headers (esp_log.h, freertos/*) so TunerService.cpp's
scanForStation logging/pacing compiles for station_service_test /
integration_service_test instead of running stale binaries
- Added WifiScanner and WebRadioService manual sections; filled in missing
Doxygen docs on BluetoothService, i2s_sdata_probe, test_firmware, Bt1035At
- Ignore clangd's .cache/ index directory
Also includes prior uncommitted work carried in the tree: Wi-Fi/Bluetooth
device scan REST API and UI (WifiScanner, BT scan), SigmaStudio TCP bridge,
and the current ADAU1701 SigmaStudio DSP program export.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Switch BT1035 bring-up from Line-In to I2S slave (AT+AUXCFG=3, AT+I2SCFG=67) to match the ADAU1701 PCM routing, confirm 2 kΩ I2C pull-ups on R1/R16, and sync firmware docs, AGENTS rules, and the DATASHEET bundle.
Co-authored-by: Cursor <cursoragent@cursor.com>
Align README, manual, and backlog to 0.8.4; add Web UI System tab for OTA/DSP uploads, serial in health header, FM seek down, and BT1035 paired list plus auto-reconnect API.
Co-authored-by: Cursor <cursoragent@cursor.com>
Replace angle-bracket suffix placeholders that Doxygen parsed as invalid
HTML tags, restoring a clean WARN_AS_ERROR build on Ubuntu CI.
Co-authored-by: Cursor <cursoragent@cursor.com>
Stream application binaries to the inactive OTA slot via POST /api/system/ota,
validate the esp_app_desc project name in core, and cancel rollback after a
healthy network boot through OtaService::confirmBoot().
Co-authored-by: Cursor <cursoragent@cursor.com>
Decouple the SigmaStudio RAM download from compiled-in adau1701_program.c:
DRAD v1 blobs in the dsp partition with embedded fallback, POST /api/dsp/program,
and host-tested blob parse/serialize helpers.
Co-authored-by: Cursor <cursoragent@cursor.com>
Read the factory 24AA025E48 serial after ADAU I2C boot, derive SoftAP SSID, BT name, STA hostname, and expose serialNumber on GET /api/health with graceful fallbacks.
Co-authored-by: Cursor <cursoragent@cursor.com>
Replace the services stub with IntegrationService for boot preset recall and tune orchestration, persist last preset in NVS, and remove invalid @return tags that broke CI on T4 metadata headers.
Co-authored-by: Cursor <cursoragent@cursor.com>
Ship station reorder, DAB playing ids in presets, RDS PS/RT and DAB DLS in tuner status, Si4684 data-service read, host tests, and UI now-playing lines.
Co-authored-by: Cursor <cursoragent@cursor.com>
Clear doc-block warnings so doxygen exits 0, add GitHub Actions
for host tests, Doxygen, and manual sync, and document CI in the manual.
Co-authored-by: Cursor <cursoragent@cursor.com>
Expose discoverable mode and A2DP control over REST, add persisted
DAB/FM preset list with web UI, and document gaps in docs/TODO.md.
Co-authored-by: Cursor <cursoragent@cursor.com>
Expose Si4684, ADAU1701, and BT1035 boot flags via CompanionChipStatus after
HardwareBootstrap; update API manual schema for Slice 8.
Co-authored-by: Cursor <cursoragent@cursor.com>
Implement Bt1035Driver AT init (AT+AUXCFG=1), core AT parser with host tests,
wire boot into HardwareBootstrap, and document DAB/FM tuning workflows in ch-si4684.
Co-authored-by: Cursor <cursoragent@cursor.com>
Expose POST /api/audio/stereo-enhance and bass-enhance with 0–100 levels,
persist enhancements in AudioProfile, and document the virtual EQ mapping in
the manual and SigmaStudio chapter.
Co-authored-by: Cursor <cursoragent@cursor.com>
Document the ADAU1701 schematic chain (sigma-chain.jpg), cross-link from
hardware/firmware chapters, skip safeload on fixed high-pass band 0, and
match EqProfile default peaking frequencies to SigmaStudio.
Co-authored-by: Cursor <cursoragent@cursor.com>
Safeload mixer/EQ/master on the ADAU1701, persist AudioProfile in NVS,
expose /api/audio routes and web UI controls, with host tests and manual sync.
Co-authored-by: Cursor <cursoragent@cursor.com>
Implement ESP-IDF walking skeleton with SoftAP, health API, and host
tests, then Slice 2 ISecureStore/NvsSecureStore, STA join, POST
/api/wifi, and the provisioning web UI.
Co-authored-by: Cursor <cursoragent@cursor.com>
micheleandClaude Sonnet 5