BT1035Driver::boot() had zero retry on the reset+AT-init sequence — a
single hardware RESET# pulse followed immediately by AT commands,
with no second attempt if the module didn't come up in time. This is
the most plausible explanation for the intermittent "no spontaneous
UART bytes after hardware reset" / "AT init failed" boot failures
logged in docs/si4684-rf-investigation-report.md and observed again
live this morning on otherwise-identical hardware/wiring — classic
power-up timing jitter, not a permanent fault. Extracted the reset+
init sequence into resetAndInitOnce() and wrapped it in a 3-attempt
retry loop with a short delay between attempts; the one-time GPIO
config and UART driver install stay outside the loop since they don't
need repeating. Root cause of the underlying jitter is still open.
BluetoothJson.hpp was the only *Json.hpp module in the core with zero
host test coverage (status/scan/paired serialisation, auto-reconnect/
connect/speaker parsing) — every sibling module already has one.
Added bluetooth_json_test.cpp following the existing tuner_json_test
pattern; ctest now covers 20 suites instead of 19.
Documentation catch-up, found doing a full firmware re-review at the
user's request:
- POST /api/tuner/calibrate-antenna and the antcap field on
POST /api/tuner/tune (added in a previous commit, never documented)
are now in ch-api.tex.
- kFirmwareVersion was still hardcoded "0.8.5" despite the RF fixes,
BLE provisioning, phone streaming, antenna calibration, and generic
DSP param API landed since that version's actual release commit
(0a1188a). Bumped to 0.9.0 everywhere it's mentioned (health JSON,
the manual's title page, intro, classes, and API chapters).
- instructions.md and docs/TODO.md still described the firmware as
frozen at 0.8.5 awaiting hardware-in-the-loop testing that has since
happened extensively; docs/TODO.md's H5 verdict specifically still
said "suspect U6 RF ground (re-open PCBWay)" for a bug that turned
out to be firmware, not hardware — actively misleading, corrected.
Both files now summarise the post-0.8.5 HIL findings and current
open items (BT1035 root cause, intermittent HTTP unresponsiveness
under load, antenna-limited signal quality, possibly-undersized 24 KB
nvs partition).
Verified: idf.py build, doxygen (0 warnings), check-manual-sync,
check_si4684_blobs, ctest (20/20), two-pass xelatex manual build all
green. Flashed and confirmed live: fw reports 0.9.0, BT1035 booted on
the first attempt post-flash.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0178rASQ6ZETPMUamvpoR2KR
ch-api.tex only covered a subset of the routes SetupWebServer.cpp
actually registers. Backfilled the ones that had grown undocumented
over the last several sessions, plus this session's three new ones:
- POST /api/wifi/scan (existed, undocumented)
- POST /api/tuner/scan, POST /api/tuner/scan/full (full FM band scan,
this session's item 1)
- POST /api/audio/beep, GET /api/dsp/params, PUT /api/dsp/param
(generic ADAU1701 parameter access, this session's item 4)
- PUT /api/stream/phone (phone PCM streaming, item 2, commit e8f79c4)
- GET/POST /api/streaming (web radio config, existed, undocumented)
- POST /api/bluetooth/scan, POST /api/bluetooth/connect,
GET/POST/DELETE /api/bluetooth/speaker, POST /api/bluetooth/reconnect
(existed, undocumented)
Also added a subsection under "Boot and network state machine"
covering BLE provisioning (commit 74c40ee) — it isn't an HTTP
endpoint so it doesn't fit the \apiendpoint table, but belongs next
to the SoftAP/STA state description it's additive to.
Verified: tools/check-manual-sync.py passes, and a full two-pass
xelatex build of the manual compiles clean (no undefined references,
no errors) with the new sections in place.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_0178rASQ6ZETPMUamvpoR2KR
Streaming (main feature this session):
- New WebRadioConfig/WebRadioJson core types, ISecureStore-backed persistence
- New webradio::WebRadioService (thread-safe live config) + GET/POST /api/streaming
- web_radio_stream task now runtime-toggleable (no reboot), no hardcoded URL
- Content-Type diagnostic: warns clearly when a URL is a webpage, not an audio stream
Boot cleanup:
- Removed boot-time auto FM/DAB tune, auto-beep, and the (now-concluded) Si4684
crystal IBIAS/CTUN empirical sweep from main.cpp — tuning/beep are on-demand
via the existing REST API only
Web UI:
- Modernized styling (cards, gradients, toggle switches, light/dark theme)
- New Stream tab wired to /api/streaming
Fixes found via real idf.py build (not just clangd):
- Restored wrongly-removed si4684/Si4684Tuner.hpp include in main.cpp
- Fixed MP3Decode() argument types in web_radio_stream.cpp (unsigned char**/int*)
Quality-gate fixes:
- Host-test stub headers (esp_log.h, freertos/*) so TunerService.cpp's
scanForStation logging/pacing compiles for station_service_test /
integration_service_test instead of running stale binaries
- Added WifiScanner and WebRadioService manual sections; filled in missing
Doxygen docs on BluetoothService, i2s_sdata_probe, test_firmware, Bt1035At
- Ignore clangd's .cache/ index directory
Also includes prior uncommitted work carried in the tree: Wi-Fi/Bluetooth
device scan REST API and UI (WifiScanner, BT scan), SigmaStudio TCP bridge,
and the current ADAU1701 SigmaStudio DSP program export.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Refresh BOM (2026-07-09 CSV), Gerbers, EasyEDA project, pick-and-place, and schematic export; document corrected ADAU crystal/PLL strapping and Si4684 reference clock in the manual; add PCBWay acknowledgement on the back cover only.
Co-authored-by: Cursor <cursoragent@cursor.com>
Add wrapping table columns, breakable paths, and ragged callout boxes in digiradio-manual.sty, then reflow long endpoint headings, JSON examples, and hardware/driver tables to stay within page margins.
Co-authored-by: Cursor <cursoragent@cursor.com>
Add gitignore rules for aux, log, toc, fls, fdb_latexmk, listing, out, and pdf so only source .tex/.sty stay in version control.
Co-authored-by: Cursor <cursoragent@cursor.com>
Switch BT1035 bring-up from Line-In to I2S slave (AT+AUXCFG=3, AT+I2SCFG=67) to match the ADAU1701 PCM routing, confirm 2 kΩ I2C pull-ups on R1/R16, and sync firmware docs, AGENTS rules, and the DATASHEET bundle.
Co-authored-by: Cursor <cursoragent@cursor.com>
Rename conflicting TikZ step style to drstep, add missing ch:firmware label, and use TeX Gyre Heros font fallback instead of Linux Biolinum O.
Co-authored-by: Cursor <cursoragent@cursor.com>
Align README, manual, and backlog to 0.8.4; add Web UI System tab for OTA/DSP uploads, serial in health header, FM seek down, and BT1035 paired list plus auto-reconnect API.
Co-authored-by: Cursor <cursoragent@cursor.com>
Stream application binaries to the inactive OTA slot via POST /api/system/ota,
validate the esp_app_desc project name in core, and cancel rollback after a
healthy network boot through OtaService::confirmBoot().
Co-authored-by: Cursor <cursoragent@cursor.com>
Decouple the SigmaStudio RAM download from compiled-in adau1701_program.c:
DRAD v1 blobs in the dsp partition with embedded fallback, POST /api/dsp/program,
and host-tested blob parse/serialize helpers.
Co-authored-by: Cursor <cursoragent@cursor.com>
Read the factory 24AA025E48 serial after ADAU I2C boot, derive SoftAP SSID, BT name, STA hostname, and expose serialNumber on GET /api/health with graceful fallbacks.
Co-authored-by: Cursor <cursoragent@cursor.com>
Enable GPIO_PULLDOWN_ENABLE during gpio_config so RSTB cannot glitch high before gpio_set_level(0), and add manual validation notes explaining why the internal pull-down complements the external one.
Co-authored-by: Cursor <cursoragent@cursor.com>
Update READMEs, manual chapters, agent guides, CONTRIBUTING, and TODO to reflect T1–T8 done, encrypted NVS, CI gates, and pending HIL checklist.
Co-authored-by: Cursor <cursoragent@cursor.com>
Add initEncryptedStorage, development-mode Kconfig defaults, production overlay, and security HIL docs; wire NetBootstrap through encrypted NVS bring-up.
Co-authored-by: Cursor <cursoragent@cursor.com>
Add now-playing view with metadata polling, six-band EQ controls, full REST coverage, companion-chip badges, and gzip-www helper for the embedded setup page.
Co-authored-by: Cursor <cursoragent@cursor.com>
Replace the services stub with IntegrationService for boot preset recall and tune orchestration, persist last preset in NVS, and remove invalid @return tags that broke CI on T4 metadata headers.
Co-authored-by: Cursor <cursoragent@cursor.com>
Ship station reorder, DAB playing ids in presets, RDS PS/RT and DAB DLS in tuner status, Si4684 data-service read, host tests, and UI now-playing lines.
Co-authored-by: Cursor <cursoragent@cursor.com>
Clear doc-block warnings so doxygen exits 0, add GitHub Actions
for host tests, Doxygen, and manual sync, and document CI in the manual.
Co-authored-by: Cursor <cursoragent@cursor.com>
Expose discoverable mode and A2DP control over REST, add persisted
DAB/FM preset list with web UI, and document gaps in docs/TODO.md.
Co-authored-by: Cursor <cursoragent@cursor.com>
Expose Si4684, ADAU1701, and BT1035 boot flags via CompanionChipStatus after
HardwareBootstrap; update API manual schema for Slice 8.
Co-authored-by: Cursor <cursoragent@cursor.com>
Implement Bt1035Driver AT init (AT+AUXCFG=1), core AT parser with host tests,
wire boot into HardwareBootstrap, and document DAB/FM tuning workflows in ch-si4684.
Co-authored-by: Cursor <cursoragent@cursor.com>
Expose POST /api/audio/stereo-enhance and bass-enhance with 0–100 levels,
persist enhancements in AudioProfile, and document the virtual EQ mapping in
the manual and SigmaStudio chapter.
Co-authored-by: Cursor <cursoragent@cursor.com>
Document the ADAU1701 schematic chain (sigma-chain.jpg), cross-link from
hardware/firmware chapters, skip safeload on fixed high-pass band 0, and
match EqProfile default peaking frequencies to SigmaStudio.
Co-authored-by: Cursor <cursoragent@cursor.com>
Safeload mixer/EQ/master on the ADAU1701, persist AudioProfile in NVS,
expose /api/audio routes and web UI controls, with host tests and manual sync.
Co-authored-by: Cursor <cursoragent@cursor.com>
Add ch-api.tex for REST endpoints and boot flow, update ch-firmware,
ch-build, and ch-intro. Extend CONTRIBUTING, instructions, and README
with manual sync checks and API reference.
Co-authored-by: Cursor <cursoragent@cursor.com>
Implement ESP-IDF walking skeleton with SoftAP, health API, and host
tests, then Slice 2 ISecureStore/NvsSecureStore, STA join, POST
/api/wifi, and the provisioning web UI.
Co-authored-by: Cursor <cursoragent@cursor.com>
micheleandClaude Sonnet 5