The 2026-08-16 IBP=1 override (commit 6974095) was applied alongside a
separate, simultaneous fix to Si4684's PIN_CONFIG_ENABLE and credited
with turning static into audible music. SerialInputRegister (0x081F) is
a single register shared by every SDATA_INx pin on the ADAU1701, so the
override also applied to the ESP32 streaming input, not just Si4684's.
Live A/B testing today (DAB, FM, and ESP32 web-radio, all isolated via
mixer gain, with and without ADAU1701 DSP bypass, with and without BT
A2DP codec changes) narrowed the hiss to this one shared register.
Removing the override and leaving IBP at its compiled default (0x00)
resolved the hiss on both the Si4684 and ESP32 paths, confirmed by ear.
Also:
- Add a runtime HTTP API (GET/POST /api/bluetooth/a2dp-codec) to change
the BT1035 A2DP codec bitmask without reflashing, used to rule out
AAC/SBC codec choice as a contributing cause.
- Extend the ADAU1701 boot-time EQ diagnostic to read back all 6 bands
(previously band 0 only) using the correct 5.23 fixed-point format.
- Note EEPROM persistence for ANTCAP/crystal calibration as TODO.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
RESET# (pin 8) is no longer driven at all: reconfigured as a floating
input relying entirely on the module's own internal pull-up per
datasheet §4.8, as a diagnostic test to rule out host-side RESET# drive
as a contributor to intermittent boot failures.
SYS_CTRL (pin 34) now performs a genuine LOW(2.5s)->HIGH power-cycle on
every resetAndInitOnce() call rather than being asserted once ever:
previously every later retry from bt1035RetryTask silently reused an
already-HIGH SYS_CTRL line without ever actually power-cycling the
module.
Added read-only diagnostics on the CTS/RTS pins (physically wired,
named in board_pins.hpp since their original definition, never
configured by any driver code, host flow control disabled) to observe
their level around the boot-banner wait, after reviewing a sibling
project's PinScope report and re-reading the datasheet's UART flow
control and PA_MUTE default-function documentation.
Across ~45 minutes of live testing after these changes, zero successful
boots were observed - inconclusive on whether this improves anything,
but each change is independently correct per the datasheet. Escalated
to Feasycom support with the full findings. Documented in the RF
investigation report and TODO.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Git archaeology traced the boot sequence back to fd9d4ae (2026-08-15,
documented 5/5 clean boots), which removed a redundant AT+RESET and added
the boot-banner listen window in a single commit. Comparing that
validated design to today's working tree found one real structural
deviation: an intra-boot() retry loop (2 attempts, only 300ms between
hardware reset pulses) added earlier today, which never existed in the
validated baseline. The BT1035 datasheet's own Reset Protection timeout
(typically >1.8s) means a second pulse fired only 300ms later may not
reach a clean power-off state before repowering.
Removed the intra-boot() retry loop entirely (kBootAttempts,
kBootRetryDelayMs deleted) — boot() now makes exactly one attempt per
call, matching fd9d4ae. Retries remain exclusively at the
bt1035RetryTask level (whole clean boot() calls, confirmed live at
~31.8s apart). Banner wait (25s) and GPIO readback left untouched.
Documented the full commit-by-commit analysis and live test result
(structurally correct, hit-rate inconclusive on this sample) in the RF
investigation report and TODO for future sessions.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Extend the FM-only ANTCAP antenna-varactor override to DAB, mirroring the
existing mechanism end to end (driver, tuner, service, EEPROM storage,
HTTP API). Live sweep on real hardware found no ANTCAP value beating
auto-tune on the ensembles tested, so DAB stays on auto-tune by default.
Also fix BT1035 boot: the module's real boot banner doesn't appear until
~18-24s after RESET# releases, not the 3.5s previously waited; add a
2-attempt retry and a baud-rate probe fallback for diagnostics.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Redundant AT+RESET sent right after the hardware RESET# pulse could interrupt
the module mid bring-up; boot-banner probe window (1500ms) was too short for
the real +VER banner (~5s), causing spurious "AT init failed". 5/5 clean
boots after fix vs ~1/13 before.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Streaming (main feature this session):
- New WebRadioConfig/WebRadioJson core types, ISecureStore-backed persistence
- New webradio::WebRadioService (thread-safe live config) + GET/POST /api/streaming
- web_radio_stream task now runtime-toggleable (no reboot), no hardcoded URL
- Content-Type diagnostic: warns clearly when a URL is a webpage, not an audio stream
Boot cleanup:
- Removed boot-time auto FM/DAB tune, auto-beep, and the (now-concluded) Si4684
crystal IBIAS/CTUN empirical sweep from main.cpp — tuning/beep are on-demand
via the existing REST API only
Web UI:
- Modernized styling (cards, gradients, toggle switches, light/dark theme)
- New Stream tab wired to /api/streaming
Fixes found via real idf.py build (not just clangd):
- Restored wrongly-removed si4684/Si4684Tuner.hpp include in main.cpp
- Fixed MP3Decode() argument types in web_radio_stream.cpp (unsigned char**/int*)
Quality-gate fixes:
- Host-test stub headers (esp_log.h, freertos/*) so TunerService.cpp's
scanForStation logging/pacing compiles for station_service_test /
integration_service_test instead of running stale binaries
- Added WifiScanner and WebRadioService manual sections; filled in missing
Doxygen docs on BluetoothService, i2s_sdata_probe, test_firmware, Bt1035At
- Ignore clangd's .cache/ index directory
Also includes prior uncommitted work carried in the tree: Wi-Fi/Bluetooth
device scan REST API and UI (WifiScanner, BT scan), SigmaStudio TCP bridge,
and the current ADAU1701 SigmaStudio DSP program export.
Co-Authored-By: Claude Sonnet 5 <noreply@anthropic.com>
Switch BT1035 bring-up from Line-In to I2S slave (AT+AUXCFG=3, AT+I2SCFG=67) to match the ADAU1701 PCM routing, confirm 2 kΩ I2C pull-ups on R1/R16, and sync firmware docs, AGENTS rules, and the DATASHEET bundle.
Co-authored-by: Cursor <cursoragent@cursor.com>
Align README, manual, and backlog to 0.8.4; add Web UI System tab for OTA/DSP uploads, serial in health header, FM seek down, and BT1035 paired list plus auto-reconnect API.
Co-authored-by: Cursor <cursoragent@cursor.com>
Read the factory 24AA025E48 serial after ADAU I2C boot, derive SoftAP SSID, BT name, STA hostname, and expose serialNumber on GET /api/health with graceful fallbacks.
Co-authored-by: Cursor <cursoragent@cursor.com>
Expose discoverable mode and A2DP control over REST, add persisted
DAB/FM preset list with web UI, and document gaps in docs/TODO.md.
Co-authored-by: Cursor <cursoragent@cursor.com>
Implement Bt1035Driver AT init (AT+AUXCFG=1), core AT parser with host tests,
wire boot into HardwareBootstrap, and document DAB/FM tuning workflows in ch-si4684.
Co-authored-by: Cursor <cursoragent@cursor.com>
Implement ESP-IDF walking skeleton with SoftAP, health API, and host
tests, then Slice 2 ISecureStore/NvsSecureStore, STA join, POST
/api/wifi, and the provisioning web UI.
Co-authored-by: Cursor <cursoragent@cursor.com>
micheleandClaude Sonnet 5