# FPGA Neural Network Engine Hardware Neural Network Engine based on FPGA + dedicated RAM. The project implements a **parametric hardware accelerator for neural networks**, designed to be reusable across different embedded systems and applications. The fundamental design principle is that the neural-network computation is performed entirely inside the FPGA, while the host system communicates with the engine through a simple hardware-independent interface such as SPI. --- ## 1. Project Goal The goal of this project is to develop a reusable **Neural Network Engine implemented in FPGA hardware**. The engine is composed of: - FPGA; - dedicated RAM connected to the FPGA; - host interface, initially SPI and potentially Dual SPI. The host system is not part of the neural-network computational datapath. Possible host systems include: - Linux SoCs; - Raspberry-Pi-like systems; - ESP32; - microcontrollers; - other embedded processors; - development PCs. The same Neural Network Engine architecture should therefore be usable in completely different systems. ```text HOST SYSTEM ┌─────────────────────────┐ │ │ │ Linux / ESP32 / MCU │ │ │ │ Configuration │ │ Training │ │ Control │ └────────────┬────────────┘ │ SPI / Dual SPI │ ▼ ┌─────────────────────────┐ │ FPGA │ │ │ │ Neural Network Engine │ │ │ │ Compute / Control │ │ │ └────────────┬────────────┘ │ │ Dedicated RAM ``` --- # 2. Architectural Principle The FPGA is the actual neural-network accelerator. The RAM required by the neural network is physically associated with the FPGA and is **not part of the host system memory**. The host only provides: - configuration; - network parameters; - input data; - control; - result retrieval. The neural-network calculations themselves are executed by the FPGA. This separation is a fundamental architectural requirement. --- # 3. Hardware Configuration vs Network Configuration An important distinction is made between the **hardware architecture of the accelerator** and the **parameters of the neural network**. ## 3.1 FPGA hardware configuration The physical architecture of the Neural Network Engine is defined when the FPGA design is synthesized and implemented. Typical hardware parameters include: ```text N_INPUTS N_NEURONS N_LAYERS PARALLEL DATA_WIDTH ACCUMULATOR_WIDTH ``` These parameters can therefore be Verilog/SystemVerilog parameters or equivalent synthesis-time configuration values. For example: ```text N_INPUTS = 32 N_NEURONS = 4 PARALLEL = 8 ``` defines a specific hardware implementation optimized for that architecture. The resulting FPGA bitstream contains the corresponding datapath. --- ## 3.2 Neural-network configuration Once the FPGA has been configured and initialized, the actual neural-network parameters can be loaded through the host interface. These parameters may include: - weights; - biases; - activation parameters; - quantization parameters; - network-specific constants. These values are stored in the RAM associated with the FPGA. Therefore: ```text FPGA BITSTREAM │ │ defines hardware architecture ▼ ┌─────────────────────┐ │ Neural Network │ │ Hardware Engine │ └──────────┬──────────┘ │ │ loads ▼ ┌─────────────────────┐ │ Dedicated RAM │ │ │ │ weights │ │ biases │ │ parameters │ │ buffers │ └─────────────────────┘ ``` This provides an important separation between **hardware specialization** and **network data**. --- # 4. Application-Specific Neural Networks The Neural Network Engine is not intended to implement one fixed neural network. Instead, each application can define its own network. For example: ```text Application A 16 inputs 8 neurons 1 output Application B 32 inputs 16 neurons 4 outputs Application C 64 inputs multiple layers custom parallelism ``` The FPGA hardware can then be generated specifically for the required architecture. This allows the design to exploit the FPGA resources efficiently rather than implementing a completely generic and potentially inefficient neural-network processor. --- # 5. Parametric Compute Engine The current implementation contains a parametric neural-network layer. A validated configuration is: ```text N_INPUTS = 32 N_NEURONS = 4 PARALLEL = 8 ``` The datapath processes the inputs in parallel groups. Conceptually: ```text 32 inputs │ ├── 8 parallel MACs │ ├── 8 parallel MACs │ ├── 8 parallel MACs │ └── 8 parallel MACs │ ▼ Accumulation │ ▼ Bias │ ▼ Activation │ ▼ Output ``` The architecture is intended to scale by changing the synthesis parameters. --- # 6. Current Functional Validation The `32 × 4 / PARALLEL = 8` configuration has been successfully simulated. Test output: ```text ======================================== PARAMETRIC LAYER TEST N_INPUTS = 32 N_NEURONS = 4 PARALLEL = 8 ======================================== PASS N0: 8192 PASS N1: 4096 PASS N2: 0 (ReLU) PASS N3: 16384 ======================================== PARAMETRIC TEST PASSED ======================================== ``` Validated functionality: - multiple inputs; - multiple neurons; - parallel MAC processing; - accumulation across multiple input groups; - bias handling; - independent neuron outputs; - ReLU activation; - parametric layer architecture. The corresponding test has been committed to the repository. Commit: ```text test: validate parametric 32x4 layer with parallelism 8 ``` --- # 7. FPGA Boot and Initialization The FPGA is configured during system initialization using its normal FPGA configuration mechanism. The FPGA bitstream defines the hardware architecture of the Neural Network Engine. Conceptually: ```text Power-on │ ▼ FPGA configuration │ │ bitstream ▼ Neural Network Engine available │ ▼ Host initialization │ │ SPI ▼ Load network parameters │ ▼ Load weights / biases │ ▼ Engine ready ``` This means that the host does **not dynamically construct the FPGA datapath** during normal operation. The datapath already exists in hardware. The host configures the network data that the datapath operates on. --- # 8. Host Interface The primary external interface is intended to be: ```text SPI ``` with possible future support for: ```text Dual SPI ``` The interface must remain independent of the host operating system. The same hardware protocol should therefore be usable from: ```text Linux ESP32 MCU PC ``` The host interface should provide access to: - control registers; - status; - network configuration; - RAM; - input data; - output data; - start/stop control; - completion status. A conceptual command sequence is: ```text RESET │ ▼ CONFIGURE │ ▼ LOAD NETWORK PARAMETERS │ ▼ LOAD WEIGHTS │ ▼ LOAD BIASES │ ▼ LOAD INPUT │ ▼ START │ ▼ WAIT FOR DONE │ ▼ READ OUTPUT ``` ## 8.1 SPI Protocol v1 (draft, 2026-09-02) Concrete opcode-level draft of the section above, written before any Phase 4 RTL. Opcode values and the exact set of commands are illustrative/example at this stage, not frozen — the framing rules (MSB-first, explicit length, sticky STATUS.done) and the two decisions already made (explicit length field over CS-delimited streaming; a runtime READ_CONFIG command) are the parts intended to stick; the opcode table itself is expected to be revised as Phase 4 RTL work starts. **Physical layer:** SPI Mode 0 (CPOL=0, CPHA=0), MSB-first, single SPI for v1 (Dual SPI is a future extension per §8, not addressed here). The FPGA is always SPI slave. One command per CS-low period; byte 0 of every transaction is the opcode. **Multi-byte fields** are big-endian (most significant byte first). Byte addresses are `ADDR_WIDTH`-bit (23 bits today, from `rtl/neuron_memory.v` — sized for a full 8 MiB PSRAM, see `docs/FPGA-Neural-Hardware-Design.md` §3), carried in a 3-byte field with the top bit reserved as 0. **Length is explicit**, not CS-edge-delimited: `WRITE_RAM`/`READ_RAM` carry a 2-byte length field, so the SPI controller only needs a byte counter, not CS-edge detection mid-transfer. ### Opcode table | Opcode | Name | Payload (host → FPGA) | Response (FPGA → host) | Function | |---|---|---|---|---| | 0x00 | NOP | — | — | No operation (idle/dummy clocking) | | 0x01 | WRITE_RAM | addr(3B) + len(2B) + `len` data bytes | — | Write a block into PSRAM (X, weights, bias, network params) | | 0x02 | READ_RAM | addr(3B) + len(2B) | `len` data bytes | Read a block back from PSRAM | | 0x0F | RESET | — | — | Synchronous reset pulse to the compute engine (`neuron_memory`) and clears the STATUS latch below. Does **not** erase PSRAM contents. Kept as a distinct opcode from NOP. | | 0x10 | SET_BASE | sel(1B) + addr(3B) | — | Sets `x_base`(sel=0) / `w_base`(sel=1) / `bias_addr`(sel=2) / `table_base`(sel=3) / `buf_a_base`(sel=4) / `buf_b_base`(sel=5) / `activation`(sel=6) / `n_inputs_real`(sel=7) / `n_neurons_real`(sel=8) — sel=6..8 are single-layer/manual-path registers only (RUN_NETWORK reads the equivalent fields per-layer from the descriptor table instead). sel=6 uses only the low 2 bits of the low address byte (see `neuron_parallel.v`'s `ACT_*` localparams; reset default `ACT_RELU`). sel=7/8 use the low 2 of the 3 address bytes as a 16-bit BE value (reset default = this bitstream's build-time `N_INPUTS`/`N_NEURONS`) — see "Runtime network width" below. | | 0x20 | START | — | — | Pulses `start` on `neuron_memory` directly (single-layer/manual path); ignored (no-op) if the engine is busy in any form (single-layer or a RUN_NETWORK job) | | 0x21 | STATUS | — | 1 byte | bit0=`busy` (live, OR of the single-layer and RUN_NETWORK busy signals), bit1=`done` (**sticky, clear-on-read**; latches on the *final* layer's completion for a RUN_NETWORK job, not each intermediate layer), bits7:2 reserved=0 | | 0x22 | READ_OUTPUT | — | `N_NEURONS` bytes | `y_bus`, neuron-major (byte 0 = neuron 0) | | 0x23 | RUN_NETWORK | num_layers(1B) | — | Phase 5: pulses `layer_sequencer`'s `run_start` to chain `num_layers` (1..N_LAYERS) runs of `neuron_memory` using the descriptor table at `table_base` and the ping-pong buffers at `buf_a_base`/`buf_b_base`; layer 0 reads from `x_base`. Each layer's activation (see below) is read per-layer from the descriptor table, independent of the single-layer path's `activation` register. Ignored (no-op) if the engine is already busy. | | 0x30 | READ_CONFIG | — | 8 bytes | Hardware config record, see below | **Why STATUS.done is sticky / clear-on-read:** in `rtl/neuron_memory.v` `done` is a single-cycle pulse (asserted for exactly one clock in `STATE_WAIT_N`, deasserted the next cycle). A host polling over SPI — orders of magnitude slower than the FPGA clock — would almost certainly miss a raw one-cycle pulse. The SPI register bank must therefore latch `done` into a sticky bit on the pulse, and clear it when the host issues `STATUS` (or `RESET`), not sample the raw `neuron_memory.done` signal directly. `busy` has no such problem (it is level-held for the whole computation) and can be read live. **READ_CONFIG payload** (fixed 8 bytes, lets one host firmware build work across different bitstreams without recompiling): | Byte(s) | Field | Source | |---|---|---| | 0 | `ADDR_WIDTH` (bits) | `neuron_memory.ADDR_WIDTH` | | 1–2 | `N_INPUTS` (16-bit BE) | `neuron_memory.N_INPUTS` | | 3 | `N_NEURONS` | `neuron_memory.N_NEURONS` | | 4 | `PARALLEL` | `neuron_memory.PARALLEL` | | 5 | `DATA_WIDTH` (bits) | `neuron_memory.DATA_WIDTH` | | 6–7 | protocol version (16-bit BE) | `0x0001` for this spec | **Runtime network width — one bitstream, any topology up to its build-time max (2026-09-02):** `READ_CONFIG`'s `N_INPUTS`/`N_NEURONS` report this bitstream's build-time **maximum** width (`neuron_memory`'s own synthesis parameters) — the ceiling, not necessarily what the currently-loaded network actually uses. The *real* per-run width is a separate, host-set value: - **Single-layer/manual path:** `SET_BASE` sel=7 (`n_inputs_real`) / sel=8 (`n_neurons_real`), 16-bit BE, defaulting to the build-time max on reset. - **RUN_NETWORK (multi-layer) path:** each layer's own `n_inputs_real`/`n_neurons_real` in its descriptor table entry (see the RUN_NETWORK row above and the table format below) — independent per layer, so a network can taper (e.g. 256 -> 64 -> 16 -> 4) inside one chained run. `n_inputs_real` **must be a multiple of `PARALLEL`** (the same constraint `N_INPUTS` itself is held to at elaboration time — see `rtl/neuron_parallel.v`'s parameter guard — now the host's runtime responsibility instead of a build-time check). Both fields directly bound the hardware's own loops (`neuron_memory`'s X/W RAM reads, `neuron_parallel`'s MAC group count, and — for RUN_NETWORK — the ping-pong copy-out length): a layer that only uses part of the bitstream's max width genuinely computes and copies out faster, not just "as if" narrower. No zero-padding of RAM is needed for the unused tail (contrast with the old padding-only convention this replaced) — data beyond `n_inputs_real`/`n_neurons_real` is simply never read. **Example session** (fills in the conceptual sequence above with concrete opcodes): ```text RESET -> 0x0F READ_CONFIG -> 0x30 (host learns N_INPUTS/N_NEURONS/...) WRITE_RAM (weights) -> 0x01 ... WRITE_RAM (biases) -> 0x01 ... SET_BASE (X/W/BIAS) -> 0x10 x3 WRITE_RAM (input X) -> 0x01 ... START -> 0x20 poll STATUS -> 0x21 (until done bit set; clears on this read) READ_OUTPUT -> 0x22 ``` **RUN_NETWORK (Phase 5) example session:** ```text WRITE_RAM (layer descriptor table) -> 0x01 ... (N_LAYERS entries of w_base(3B)+bias_addr(3B)+activation(1B)+n_inputs_real(2B)+n_neurons_real(2B), MSB-first) WRITE_RAM (weights/biases per layer, X for layer 0) -> 0x01 ... SET_BASE (X/TABLE/BUF_A/BUF_B) -> 0x10 x4 RUN_NETWORK(num_layers) -> 0x23 poll STATUS -> 0x21 (until done bit set; clears on this read) READ_OUTPUT -> 0x22 (final layer's y_bus) ``` Not yet decided / explicitly out of scope for v1: Dual SPI framing, a CRC/checksum on transfers (SPI is assumed reliable for a board-level trace in v1). Multi-layer sequencing itself (RUN_NETWORK, opcode 0x23) is implemented per `rtl/layer_sequencer.v` and the table above. --- # 9. Dedicated FPGA RAM The RAM is considered part of the Neural Network Engine. It is not intended to be supplied by the host system. Depending on the final architecture, RAM may contain: ```text Weights Biases Input buffers Intermediate layer buffers Output buffers Network parameters ``` The memory architecture must be designed according to: - number of parallel MAC units; - data width; - required bandwidth; - number of layers; - buffering requirements; - FPGA block-RAM resources; - possible external RAM requirements. The preferred architecture is that the FPGA directly controls this memory. --- # 10. Training Training and inference are conceptually separated. The first implementation does not require the FPGA to perform the complete training process. Training can be performed externally: ```text PC / Linux / other host │ │ training ▼ Network weights │ │ SPI ▼ FPGA RAM ``` The FPGA then performs inference using the resulting parameters. This approach greatly reduces the complexity of the initial hardware implementation. However, the architecture should not prevent future implementation of hardware-assisted or fully hardware-based training. --- # 11. Inference During inference, the host only supplies input data and retrieves the result. ```text HOST │ Input │ │ SPI ▼ ┌───────────────┐ │ FPGA │ │ │ │ Neural Network│ │ Engine │ │ │ └───────┬───────┘ │ Output │ │ SPI ▼ HOST ``` The host is not involved in the individual MAC operations. This provides: - deterministic computation; - reduced host workload; - hardware parallelism; - predictable latency; - independence from the host CPU architecture. --- # 12. Multi-Layer Architecture The current implementation starts from a single parametrized layer. The intended architecture is eventually: ```text Input │ ▼ ┌──────────────┐ │ Layer 0 │ └──────┬───────┘ │ ▼ ┌──────────────┐ │ Layer 1 │ └──────┬───────┘ │ ▼ ┌──────────────┐ │ Layer 2 │ └──────┬───────┘ │ ▼ Output ``` Intermediate data will be stored in FPGA-controlled memory buffers. The number and size of layers should ultimately be part of the hardware generation process. --- # 13. Reusability The main purpose of the architecture is reuse. A future project should be able to use the same general Neural Network Engine architecture with a different hardware configuration. For example: ```text Project A N_INPUTS = 32 N_NEURONS = 8 PARALLEL = 8 Project B N_INPUTS = 64 N_NEURONS = 16 PARALLEL = 16 Project C N_INPUTS = 128 N_NEURONS = 32 PARALLEL = 32 ``` The HDL architecture remains conceptually the same while synthesis parameters generate an implementation appropriate for the target application. --- # 14. Design Philosophy The project should be considered a: > **Reusable FPGA Neural Network Accelerator Platform** rather than a single neural-network implementation. The application determines: ```text Input size Network topology Number of layers Number of neurons Parallelism Numerical precision Activation functions Memory requirements Performance requirements ``` The hardware generator then produces the corresponding FPGA implementation. --- # 15. Development Roadmap ## Phase 1 — Parametric Layer - [x] Parametric inputs - [x] Parametric neurons - [x] Parametric parallelism - [x] Accumulation - [x] Bias - [x] ReLU - [x] 32×4 / P=8 functional test ## Phase 2 — Parameter Sweep Validate multiple combinations of: ```text N_INPUTS N_NEURONS PARALLEL ``` including configurations where the number of inputs is not an exact multiple of the parallelism. - [x] Exact-multiple sanity configs (32×8, 64×32) - [x] Non-exact-multiple configs (30×8, 20×16) - [x] Degenerate config, PARALLEL > N_INPUTS (4×8) - [x] Sweep testbench: `sim/parameter_sweep_tb.v` **Findings — FIXED (2026-09-02):** - `neuron_parallel.v` computed `GROUPS = N_INPUTS / PARALLEL` with integer division. When `N_INPUTS` was **not** an exact multiple of `PARALLEL`, only the first `GROUPS * PARALLEL` inputs were ever read by the accumulator — the remainder was silently dropped (no error, no warning). Confirmed for 30×8 → only 24 of 30 inputs summed, and 20×16 → only 16 of 20 inputs summed. - If `PARALLEL > N_INPUTS`, `GROUPS = 0` and the controller's `group_index == GROUPS-1` terminal condition was never satisfied: the neuron entered `busy` and never asserted `done` (confirmed hang, 500-cycle watchdog in the sweep bench). - Both share the same root cause (`N_INPUTS % PARALLEL != 0`, degenerate `PARALLEL > N_INPUTS` included) and both are now rejected at **elaboration time**, in simulation and synthesis alike, by a `generate` guard added to `neuron_parallel.v` (instantiates a deliberately undefined module when the parameter combination is invalid — zero cost, zero behavior change for any valid configuration). The validated datapath itself (mac8/mac_unit/accumulation/ReLU/saturation) was **not** modified. See `sim/neuron_parallel_guard_negative_nonmultiple_tb.v` and `sim/neuron_parallel_guard_negative_degenerate_tb.v` for the negative-test proof, and `sim/parameter_sweep_tb.v` for the updated positive sweep (now valid-configs-only, including `PARALLEL=2` and `PARALLEL=4`, the two best-performing values from `docs/FPGA-Neural-Datapatch-Benchmark.md`). ## Phase 3 — Memory Architecture Define: - weight memory; - bias memory; - input buffers; - output buffers; - intermediate buffers; - memory addressing; - bandwidth requirements. - [x] `neuron_memory.v`: single-neuron memory integration (N_NEURONS=1) - [x] `neuron_memory.v`: multi-neuron memory integration (N_NEURONS>1) - [ ] Intermediate/multi-layer buffers (deferred to Phase 5) - [ ] Bandwidth analysis against PSRAM timing (deferred to Phase 7) **Multi-neuron design (2026-09-02):** `neuron_memory.v` now takes an `N_NEURONS` parameter and loops over neurons in memory: `X` is read once (shared input vector), and for each neuron in turn `W` and `bias` are re-read from PSRAM and fed to a single, reused `neuron_parallel` instance — memory-bound by design, one neuron computed at a time, no change to the validated compute datapath. Addressing follows the same neuron-major convention as `layer.v`: neuron `n`'s weights live at `w_base + n*N_INPUTS` bytes, its bias at `bias_addr + n`. Output is now `y_bus` (packed, `DATA_WIDTH*N_NEURONS` bits, neuron-major), replacing the old single-neuron `y` port. Validated end to end through the full memory stack (`memory_interface` + `psram_controller` + `psram_model`) in `sim/neuron_memory_multi_tb.v` (N_NEURONS=3: scale, larger value, ReLU). `sim/neuron_memory_tb.v` (N_NEURONS=1) still passes unchanged, confirming backward compatibility. ## Phase 4 — SPI Interface Implement: - SPI controller; - register map; - RAM access; - configuration protocol; - input/output protocol; - status and control. - [x] Protocol/opcode set drafted — see §8.1 SPI Protocol v1 - [x] SPI controller RTL — `rtl/spi_slave.v` (physical layer: Mode 0, MSB-first, 3-stage CDC synchronizer for SCLK/MOSI/CS_N) - [x] Register bank RTL — `rtl/spi_engine.v` (all 8 opcodes: NOP, WRITE_RAM, READ_RAM, RESET, SET_BASE, START, STATUS, READ_OUTPUT, READ_CONFIG; sticky clear-on-read STATUS.done) - [x] RAM access passthrough RTL — `rtl/mem_arbiter.v` (fixed-priority arbiter, neuron_memory > spi_engine) + shared `int8_memory_access` instance in `rtl/spi_neuron_top.v` - [x] Testbenches: `sim/spi_slave_tb.v` (4 tests), `sim/spi_engine_tb.v` (10 tests, synthetic RAM), `sim/spi_neuron_top_tb.v` (end-to-end, **real** `psram_model.v`, no synthetic mock — RESET/READ_CONFIG/WRITE_RAM/READ_RAM/SET_BASE/START/STATUS/READ_OUTPUT all exercised purely over simulated SPI) **Real-toolchain verification (Yosys + nextpnr-ecp5 + ecppack, 2026-09-02):** - `spi_slave.v` alone: PASS, Fmax 403.23 MHz. - `spi_engine.v` alone: PASS, Fmax 191.31 MHz. Neither uses any DSP. - `spi_neuron_top.v` (full integration: SPI + arbiter + neuron_memory + PSRAM chain), N_NEURONS=1: **FAIL at 80 MHz** — Fmax ~52.58 MHz (PARALLEL=8) / ~55.85 MHz (PARALLEL=2, the benchmark's own 80 MHz-passing config in isolation). The critical path in both cases is entirely inside `neuron_parallel.v`'s saturation comparator (`> 127`, `rtl/neuron_parallel.v:127`) — zero contribution from the new SPI/arbiter logic — but its routed delay is ~57% worse than in the isolated benchmark (17.91 ns vs. 11.38 ns) due to placement/routing congestion once the SPI + PSRAM logic shares the fabric with it, not resource exhaustion (DSP utilization only 2%). This means the current auto-placed full system would need to run around 50-56 MHz to stay within timing margin at speed grade -8, not the 80 MHz target — a system-level floorplanning/pipelining problem, out of scope here and left for Phase 7 (Optimization: "pipeline depth", "FPGA resource utilization"). It does not affect functional correctness (verified independently, in simulation, against real PSRAM timing) or synthesizability (0 CHECK-pass problems, no latches). ## Phase 5 — Multi-Layer Network Implement: - multiple layers; - intermediate buffers; - layer sequencing; - configurable activation functions. - [x] `layer_sequencer.v`: chains up to `N_LAYERS` runs of a single, reused `neuron_memory` instance, reading each layer's `w_base`/`bias_addr`/`activation`/`n_inputs_real`/`n_neurons_real` from a host-written descriptor table (11 bytes/layer) and ping-ponging each layer's output between two RAM buffers (layer 0 reads the external `x_base`; layer k>0 reads the buffer layer k-1 wrote) - [x] Configurable activation functions — `neuron_parallel.v` gains a 2-bit `activation` port (`ACT_NONE`=linear+two-sided saturate, `ACT_RELU`=the original hardwired behavior, kept as the default so every pre-existing caller/testbench is unaffected), threaded through `neuron_memory.v` at runtime and settable per-layer via the descriptor table (Phase 5 path) or per-run via `SET_BASE` sel=6 (legacy single-layer path). Unit-tested directly in `neuron_parallel_tb.v` (linear pass-through + negative saturation to -128) and end-to-end in `spi_neuron_top_runnetwork_tb.v` (a real negative accumulator that ACT_RELU would have clamped to 0 comes through unclamped under ACT_NONE, verified over real SPI/RAM) - [x] Runtime network width — one synthesized bitstream serves any topology up to its build-time max: `neuron_parallel.v` gains a runtime `n_inputs_real` (bounding its MAC group loop) and `neuron_memory.v` gains `n_inputs_real`/`n_neurons_real` (bounding its X/W RAM-read loop and its neuron loop), all defaulting to the build-time max so every pre-existing caller is unaffected. Settable per-layer via the descriptor table (Phase 5 path) or per-run via `SET_BASE` sel=7/8 (legacy single-layer path). This is a **real** early termination, not just address bookkeeping — no RAM zero-padding needed for the unused tail, and it measurably runs faster: `neuron_parallel_tb.v` TEST 7 shows 3 cycles vs. 6 for a reduced-vs-full run (with garbage loaded in the skipped lanes, proving they're never read), and `neuron_memory_tb.v` TEST 5 shows the same effect through the real PSRAM stack: **209 cycles vs. 788** for an 8-of-32 vs. full-32 run. `layer_sequencer_tb.v` additionally proves a reduced `n_neurons_real` shortens the ping-pong copy-out itself (untouched RAM bytes beyond the real count, not just a differing value) - [x] `mem_arbiter.v`: extended to a third port (Port C, priority B > C > A) for the sequencer's own RAM master access - [x] `spi_engine.v`: `RUN_NETWORK` opcode (0x23) + `SET_BASE` selectors for `table_base`/`buf_a_base`/`buf_b_base`; `STATUS.busy`/`STATUS.done` extended to track the sequencer (`seq_busy`/`seq_done`) as well as `neuron_memory` directly, so `done` latches on the *last* layer only, not each intermediate one — see §8.1 - [x] `spi_neuron_top.v`: instantiates the sequencer and muxes `neuron_memory`'s control inputs between it (while `seq_busy`) and `spi_engine`'s direct-drive path (legacy single-layer mode) - [x] Testbenches: `sim/layer_sequencer_tb.v` (2-layer run: descriptor table, ping-pong addressing verified by address not just value, byte-exact output-buffer copy, `seq_busy` held across the layer boundary, `seq_done` fires exactly once, plus a reduced `n_neurons_real` proven to shorten the copy-out itself); `sim/spi_engine_tb.v` gained tests K/L/M/N (new `SET_BASE` selectors incl. activation and runtime width, `RUN_NETWORK` accept/busy-ignore gating, `STATUS` semantics) — both use a mocked `neuron_memory`, same pattern as Phase 4's `spi_engine_tb.v`; `sim/neuron_parallel_tb.v` and `sim/neuron_memory_tb.v` each gained a dedicated runtime-width test against the real datapath/real PSRAM stack (see the runtime-width bullet above for the cycle counts) - [x] Real-toolchain (Yosys + nextpnr-ecp5) synthesis/Fmax check of the extended `spi_neuron_top.v` — **worse than Phase 4 alone** in both configs checked, speed grade -8: N_INPUTS=32/N_NEURONS=1/PARALLEL=8 gives **40.57 MHz, FAIL** (Phase 4 alone: ~52.58 MHz); PARALLEL=2 gives **42.54 MHz, FAIL** (Phase 4 alone: ~55.85 MHz). The Phase 5 wiring (sequencer + mux + arbiter Port C) measurably cost 12-13 MHz of headroom on top of Phase 4's own placement-congestion problem, and the critical path itself shifted from Phase 4's saturation-comparator finding to `neuron_memory`'s `x_mem`/`w_mem` LUT-RAM read-mux tree — see the Phase 7 critical-path analysis below. - [x] `sim/spi_neuron_top_runnetwork_tb.v`: real end-to-end test, `RUN_NETWORK` driven purely over simulated SPI against the real `neuron_memory` + PSRAM chain (N_INPUTS=N_NEURONS=4, PARALLEL=2, 2 layers, hand-computed expected output verified via both `READ_OUTPUT` and a `READ_RAM` of `buf_b_base`, plus `buf_a_base`'s intermediate layer-0 output) — all PASS, and confirms the mux correctly hands `neuron_memory` back to the legacy single-layer `START` path afterward **Bug found and fixed while writing the above test (2026-09-02):** a real race in the STATUS.done sticky/clear-on-read mechanism (§8.1), present since Phase 4 and not specific to RUN_NETWORK — it only needed continuous STATUS polling racing a `done` transition to surface, which the new end-to-end test's `wait_done` polling loop finally did. `tx_byte`'s `OP_STATUS` case read `status_done_sticky`/`busy` **live/combinationally** for the whole `ST_RESP` window, while the sticky bit was cleared unconditionally on any STATUS read (`status_read_now`). If `done_event` landed while a STATUS response byte was already mid-transmission, the byte actually shifted out to the host could still be the stale pre-done value while the engine simultaneously treated the read as having delivered `done` and cleared it — silently dropping the transition forever, hanging any host polling STATUS in a tight loop. Fixed in `rtl/spi_engine.v` by latching a `status_snapshot` register once, at `OP_STATUS` opcode-accept time, and gating the sticky clear on `status_snapshot[1]` (i.e. only clear if the byte actually transmitted showed `done=1`) instead of clearing unconditionally on every STATUS read. A `done_event` that arrives too late for one snapshot is now reported on the next poll instead of being lost. All existing testbenches (`spi_slave_tb.v`, `spi_engine_tb.v`, `spi_neuron_top_tb.v`, `layer_sequencer_tb.v`) still pass unchanged. ## Phase 6 — Host Software Develop host-side drivers for: - Linux; - ESP32. The same FPGA protocol should be usable by both. ## Phase 7 — Optimization Evaluate: - pipeline depth; - MAC parallelism; - memory bandwidth; - numerical precision; - FPGA resource utilization; - latency; - throughput. **Critical-path analysis (real Yosys + nextpnr-ecp5, 2026-09-02):** both `spi_neuron_top.v` builds checked so far miss the 80 MHz target, and the shortfall grew with Phase 5 wired in: | Build | N_INPUTS/N_NEURONS/PARALLEL | Fmax | vs. 80 MHz | |---|---|---|---| | Phase 4 only (documented above) | 32/1/8 | ~52.58 MHz | -34% | | Phase 4 only (documented above) | 32/1/2 | ~55.85 MHz | -30% | | Phase 5 (this session) | 32/1/8 | 40.57 MHz | -49% | | Phase 5 (this session) | 32/1/2 | 42.54 MHz | -47% | Resource utilization is not the cause in either case: `MULT18X18D` (DSP) and `DP16KD` (block RAM) both sit at **0%** in the Phase 5 builds — `neuron_memory.v`'s `x_mem`/`w_mem` arrays (32 x INT8 each) are being inferred as **LUT-based distributed RAM**, not the ECP5's dedicated `DP16KD` block RAM, which sits completely idle. The critical path itself **shifted** between the two checks. Phase 4's finding (quoted above) pinned it on `neuron_parallel.v`'s saturation comparator (`> 127`), with routing congestion as the driver, not logic depth. In this session's Phase-5 builds the reported critical path (posedge -> posedge, `neuron_memory`'s accumulator register) instead runs through a long chain of nested `PFUMX`/`L6MUX21` LUT multiplexers reading `w_mem`/`x_mem` before reaching `acc` — consistent with a 32-entry LUT-RAM read select tree, not the saturation logic. Whether this is a genuinely different bottleneck or an artifact of where Phase 5's extra logic pushed the placer is not yet determined; it would need a placement-seed sweep (same design, several `nextpnr --seed` values) to separate "real critical path" from "this particular placement's critical path" — neither Phase 4's nor Phase 5's single P2/P8 runs establish that. **Candidate directions (not implemented, need a decision before touching the validated core further):** **Placement-seed sweep (2026-09-02) — resolved: it's structural, not noise.** Re-ran `nextpnr-ecp5` on the already-synthesized Phase 5 netlists (`top.json` reused, only placement re-seeded — no re-synth) at `--seed 1/2/3` for both P8 and P2: | Build | seed (default) | seed 1 | seed 2 | seed 3 | spread | |---|---|---|---|---|---| | P8 | 40.57 MHz | 39.70 MHz | 39.54 MHz | 40.00 MHz | 1.03 MHz (2.6%) | | P2 | 42.54 MHz | 42.82 MHz | 42.72 MHz | 45.01 MHz | 2.47 MHz (5.8%) | Both builds land in a tight band regardless of seed — nothing close to the P2/P4/P8 same-tier benchmark's own non-monotonic swings (that benchmark's design uses <2% of the device, so its placer has enormous freedom; `spi_neuron_top`'s fuller design does not). **This confirms a real structural bottleneck, not a lucky/unlucky placement** — a seed sweep or floorplan constraint will not close a ~2x gap to 80 MHz by itself; an RTL change is needed. **Candidate directions (not implemented, need a decision before touching the validated core further):** - Move `x_mem`/`w_mem` onto `DP16KD` block RAM (0% used) instead of LUT fabric — the leading candidate. The critical path runs through what looks like `w_mem`'s *write*-address decode (`neuron_memory` loads one byte per cycle into a variable index during `STATE_READ_X`/`STATE_READ_W`, which needs a full-width mux/demux in LUT fabric to steer that byte to the right register) feeding forward into the accumulator's input path — not the arithmetic itself. A block-RAM read/write port replaces that scattered LUT-based decode with a single hard macro. This is a genuine redesign, not a drop-in swap: `x_bus`/`w_bus` are currently exposed to `neuron_parallel` as one fully-parallel N_INPUTS-wide combinational bus (built by unrolling every `x_mem`/`w_mem` element every cycle); block RAM has a registered, address-in/ data-out-next-cycle read port, so `neuron_parallel`'s group processing would need to become RAM-latency-aware instead of assuming the whole bus is already valid. Real potential upside, real design effort — needs a go-ahead, not something to do opportunistically. - A pipeline register between MAC accumulation and the activation/saturate stage (this session's original guess) does **not** target the actual Phase 5 bottleneck — that finding was Phase 4's critical path (the saturation comparator), and the path moved once Phase 5's logic was wired in (see above). Keeping this noted for Phase 4-only builds; not a fix for the current problem. ## Phase 8 — Optional Hardware Training Investigate: - backpropagation; - gradient calculation; - weight updates; - hardware-assisted training. --- # 16. Long-Term Vision The final objective is to create a reusable hardware block that can be integrated into different future MIKILAB projects. ```text APPLICATION │ ┌─────────────┴─────────────┐ │ │ Linux ESP32 │ │ └─────────────┬─────────────┘ │ SPI / Dual SPI │ ▼ ┌────────────────────────┐ │ FPGA │ │ │ │ Neural Network Engine │ │ │ │ ┌────────────────────┐ │ │ │ Control │ │ │ ├────────────────────┤ │ │ │ Input Interface │ │ │ ├────────────────────┤ │ │ │ NN Compute Core │ │ │ ├────────────────────┤ │ │ │ Activation │ │ │ ├────────────────────┤ │ │ │ Output Interface │ │ │ └────────────────────┘ │ │ │ │ Dedicated RAM │ │ │ └────────────────────────┘ ``` The host platform can change without changing the fundamental Neural Network Engine architecture. The FPGA becomes a dedicated neural-computation peripheral, analogous to other hardware accelerators, but optimized specifically for the neural-network topology required by each application. --- # 17. Current Status | Component | Status | |---|---| | Parametric neuron layer | OK Working | | Parametric input count | OK | | Parametric neuron count | OK | | Parametric parallelism | OK | | Accumulation | OK | | Bias | OK | | ReLU | OK | | 32×4 / P=8 validation | OK | | Dedicated RAM architecture | OK (memory_interface + psram_controller + int8_memory_access, real-PSRAM tested) | | PSRAM page-mode burst reads | OK (2026-09-03, `psram_page_mode_tb.v`; sequential gather bandwidth +42% measured, see `FPGA-Neural-Datapatch-Benchmark.md` Appendice D) | | SPI interface | OK (spi_slave + spi_engine, all 9 opcodes incl. RUN_NETWORK, real-toolchain Fmax checked in isolation) | | Dual SPI | Future | | Multi-layer engine | - RTL + unit tests + real end-to-end (simulated SPI) done; real toolchain checked (P8: FAIL 40.57 MHz, worse than Phase 4 alone) | | Configurable activation functions | OK (ACT_NONE / ACT_RELU, per-layer via descriptor table or per-run via SET_BASE) | | Runtime network width (one bitstream, any topology up to build max) | OK (per-layer or per-run `n_inputs_real`/`n_neurons_real`, real cycle savings measured end to end) | | Linux host driver | Planned | | ESP32 host driver | Planned | | Hardware training | Future | --- ## Core architectural principle **The FPGA implements the neural-network machine. The FPGA owns its RAM. The host configures and uses the machine. A build sets the machine's *ceiling* (max layers, max width, PARALLEL); the host configures the *actual* network — layer count, per-layer input/output width, per-layer activation, and trained parameters — entirely at runtime, over SPI, into FPGA-local memory. One bitstream serves any topology up to that ceiling (2026-09-02, see §17 "Runtime network width").** This separation is the foundation of the project.