\chapter{Parameters and configurability}
\label{ch:param}

\section{Build parameters (synthesis-time)}
\begin{fnwarn}[Current, real board parameters (\code{fpga\_neural\_v2\_top.v})]
The table below reflects the real, current SDRAM-architecture top
level. The PSRAM-era \S\S\ref{ch:mem} chapters below this one describe
an earlier, real, correctly-measured milestone with different defaults
(notably \code{ADDR\_WIDTH}=23 and a PSRAM data-bus parameter) ---
superseded, not deleted, since that data remains accurate for the
architecture it was measured on.
\end{fnwarn}
\begin{tabularx}{\textwidth}{L{3.0cm} C{1.8cm} Y}
\toprule
\rowh \thd{Parameter} & \thd{Default} & \thd{Meaning} \\
\midrule
\code{DATA\_WIDTH}   & 8   & Data width (INT8), unchanged from V1. \\
\rowa \code{ACC\_WIDTH} & 32 & Accumulator width. \\
\code{P\_IN}         & 8   & Parallel MAC lanes per neuron per tile; must be even (word-level burst constraint, ch.~\ref{ch:mem}). \\
\rowa \code{ADDR\_WIDTH} & 26 & Byte-address width (widened 23$\to$26 for the 64\,MB SDRAM device, DEC-0039). \\
\code{N\_SLOTS}      & 4 & Concurrent Memory Manager$+$Neural Processor pairs. \textbf{Production configuration} --- real 8/8-seed timing closure at 64\,MHz (ch.~\ref{ch:hw} \S\ref{sec:clock-closure-current}). \\
\rowa \code{N\_NODES}   & 16  & Dependency Manager node-table depth. Sized to the largest node-id range a graph will ever use; never reclaimed (ch.~\ref{ch:arch}). \\
\code{MAX\_DEPS}     & 4   & Maximum producers a single node can list. \\
\rowa \code{QUEUE\_DEPTH} & 8 & Neural Director's own ready-job FIFO depth. \\
\code{MAX\_TILES}    & 16 & Longest activation/weight tile run a job can request. \\
\rowa \code{CLK\_FREQ\_MHZ} & 64 & Real system clock, generated by \code{ecp5\_pll\_sys\_clk.v} from the 16\,MHz oscillator; 80\,MHz confirmed NO-GO (ch.~\ref{ch:hw} \S\ref{sec:clock-closure-current}). \\
\bottomrule
\end{tabularx}

\begin{fnwarn}[\texttt{N\_SLOTS} is a real, measured trade-off, not a free parameter]
\code{N\_SLOTS}=4 is the production default: the largest slot count
that reliably closes real timing at 64\,MHz on every tested placement
seed (8/8). \code{N\_SLOTS}=8 is functionally correct (bit-exact) but
only 3/8 seeds close timing --- deferred, not production-frozen. Do
not simply raise \code{N\_SLOTS} without re-running the real 8-seed
\code{nextpnr-ecp5} matrix.
\end{fnwarn}

\section{Word-alignment constraint (post word-burst rewrite)}
Since the memory backend now moves 16-bit words rather than bytes
(ch.~\ref{ch:mem}), every tile base address the system computes
(\code{x\_base + tile\_idx*P\_IN}, and equivalently for weights) must
land on an even byte address. \code{P\_IN} even and \code{x\_base}/
\code{w\_base} themselves even together guarantee this for every tile of
every job --- true of every address this project's own testbenches use,
and a trivial constraint for any real loader/host to satisfy.

\section{Characterized configurations (PSRAM-era; see ch.~\ref{ch:hw}
\S\ref{sec:clock-closure-current} for the current SDRAM-architecture
numbers)}
\begin{tabularx}{\textwidth}{C{1.6cm} C{2.6cm} C{2.6cm} Y}
\toprule
\rowh \thd{N\_SLOTS} & \thd{Fmax, word-burst only} & \thd{Fmax, $+$activation cache} & \thd{Notes} \\
\midrule
1 & 152.44~MHz & 131.79~MHz & Best real wall-clock speedup (3.86$\times$ vs baseline); no arbitration contention possible. \\
\rowa 2 & 133.58~MHz & \textbf{87.72~MHz} & \textbf{Recommended default} --- real 2.45$\times$ speedup vs baseline, still comfortably above 80\,MHz. \\
4 & 112.07~MHz & 65.01~MHz (\FAIL) & No additional real throughput; fails 80\,MHz with the cache active. Not recommended. \\
\rowa 8 & 92.63~MHz (dataflow\_core only, no real PSRAM chain) & not re-measured & Real DSP ceiling for P\_IN=8 (64/72 MULT18X18D); a resource ceiling, not a useful operating point. \\
\bottomrule
\end{tabularx}

\section{Build versus runtime}
\begin{center}
\begin{tikzpicture}[font=\footnotesize,node distance=6mm]
 \node[fnblockD,minimum width=54mm,minimum height=17mm](b){\textbf{BUILD (synthesis)}\\[2pt]
   {\scriptsize N\_SLOTS, N\_NODES, MAX\_DEPS,}\\{\scriptsize QUEUE\_DEPTH, P\_IN, DATA\_WIDTH, ACC\_WIDTH}\\{\scriptsize $\Rightarrow$ machine ceiling}};
 \node[fnblockT,right=16mm of b,minimum width=54mm,minimum height=17mm](r){\textbf{RUNTIME (node registration)}\\[2pt]
   {\scriptsize reg\_node\_id, reg\_required, reg\_producer\_ids,}\\{\scriptsize reg\_x\_base/w\_base/n\_tiles/result\_addr}\\{\scriptsize $\Rightarrow$ the actual dependency graph}};
 \draw[fnbus] (b) -- node[fnlbl,above]{$\le$} (r);
\end{tikzpicture}
\end{center}
Full field-level description of the runtime (node registration)
interface: ch.~\ref{ch:regs}.