Files

T

micheleandCursor 6efd6e36f7 Unify root docs/ with Software/docs/manual via symlink.

Remove legacy DigiRadio_Manual.tex/PDF and stub main.tex; point docs/ at the
canonical manual. Update README and CONTRIBUTING paths.

Co-authored-by: Cursor <cursoragent@cursor.com>

2026-07-06 17:11:54 +02:00

5.3 KiB

Raw Blame History

DigiRadio

DAB+/FM Bluetooth Receiver with SigmaDSP Audio Processing

Open-source digital radio — Si4684 tuner · ADAU1701 SigmaDSP · Bluetooth aptX Adaptive · ESP32-S3

Overview

DigiRadio is an open-source digital radio receiver that combines terrestrial broadcast reception (DAB+ / DAB / FM) with a programmable audio-processing stage and high-quality Bluetooth audio output.

Incoming broadcast audio is decoded by a Silicon Labs Si4684 digital-radio receiver, processed by an Analog Devices ADAU1701 SigmaDSP (equalisation, mixing, level control), and transmitted over Bluetooth by a Qualcomm QCC3056-based Feasycom FSC-BT1035 module supporting the aptX Adaptive codec. An Espressif ESP32-S3 acts as the host controller, orchestrating the three subsystems and providing Wi-Fi/BLE connectivity and a USB service interface.

The entire tuner → DSP → Bluetooth path is fully digital (I²S, 48 kHz / 24-bit) — no analogue conversions are introduced between the tuner and the wireless link.

 FM/DAB antenna → [ Si4684 ] --I²S--> [ ADAU1701 DSP ] --I²S--> [ FSC-BT1035 ] → aptX
                       ↑                     ↑                        ↑
                       └──── SPI ──── [ ESP32-S3 host ] ──── UART ────┘
                                             │  I²C

Key Features

DAB+ / DAB / FM reception (Si4684) via external whip antenna (SMA)
Fully digital audio path — no avoidable A/D–D/A conversions
Programmable audio processing on the ADAU1701 SigmaDSP
Bluetooth 5.2 output with aptX / aptX HD / aptX Adaptive
ESP32-S3 host with native USB, Wi-Fi and BLE
USB-C powered; single-rail 3.3 V + low-noise 1.8 V for the tuner
6-layer impedance-controlled PCB, 50 × 90 mm, two ground planes
Three antennas (ESP32 2.4 GHz, BT1035 2.4 GHz, FM/DAB SMA) with proper keep-outs

Repository Structure

DigiRadio/
├── docs/                     → symlink to Software/docs/manual (canonical LaTeX manual)
│   ├── manual.tex            build with: cd docs && latexmk -lualatex manual.tex
│   └── manual.pdf
├── Hardware/
│   ├── schematics/           Schematic (PDF)
│   ├── gerber/               Gerber + drill files (fabrication)
│   ├── bom/                  Bill of Materials
│   ├── pick-and-place/       Component placement (CPL / centroid)
│   ├── easyeda/              EasyEDA source project
│   └── 3d/                   3D renders / STEP
└── Software/                 Firmware (in development — see Software/README.md)

Documentation

The full design is described in the Technical Manual, covering hardware, firmware architecture, companion-chip drivers (Si4684, ADAU1701, FSC-BT1035), the HTTP JSON API, and build instructions. LaTeX sources live in Software/docs/manual/; the repository root docs/ entry is a symbolic link to that folder (single source of truth).

Design Highlights

Topic	Choice	Rationale
Audio quality	QCC3056 / aptX Adaptive	The codec is the dominant quality factor on a wireless link; the DAC lives in the sink
Audio path	Fully digital I²S	Avoids unnecessary A/D–D/A conversions between tuner and Bluetooth
I²S master	ADAU1701 (12.288 MHz)	Clean ×256 → 48 kHz; avoids sample-rate mismatch
Stack-up	6-layer, 2× GND	Solid ground reference under RF, crystals and USB
USB routing	TOP, ref. GND	90 Ω diff achievable at manufacturable geometry
Antennas	3 zones, diagonal 2.4 GHz	Coexistence separation + full-layer keep-outs

Status

✅ Schematic — complete and reviewed
✅ PCB layout — 6-layer, DRC clean, plane continuity verified
✅ BOM — finalised (manufacturable / sourced)
🔜 Prototype — in fabrication (PCBWay)
🛠️ Firmware — in active development (released after bring-up)

Manufacturing

The board is manufactured with PCBWay as a 6-layer, impedance-controlled PCB with turnkey assembly. The FSC-BT1035 Bluetooth module is sourced from Feasycom (the footprint uses a BT806-compatible, pin-identical land pattern). See Chapter Hardware and manufacturing notes in the manual for fabrication settings and MSL-3 handling of the BT module.

License

Hardware (schematics, PCB, Gerbers, BOM): CERN-OHL-S v2 — see LICENSE
Firmware / Software: Apache-2.0 — see Software/LICENSE
Documentation: CC BY 4.0

Intellectual property of the design remains with the author. You are free to study, modify and build the hardware under the terms of the respective licenses.

Author

Michele Bigi — Open-source hardware project.

Contributions, issues and questions are welcome via the repository issue tracker.

5.3 KiB Raw Blame History Unescape Escape